Well pumps are essential in a lot of houses, especially those where you solely rely on wells to produce and make up for all of their water needs around the house. So, what happens when a well pump stops pumping water? There can be a lot of reasons why it does that. You will need to find the issue and carry out well pump repair. Here is everything you need to know about it.

Faulty Well Pressure Switch

The pressure switch is the best way to start the troubleshooting process. The pressure switch tells you whether the pressure in the pressure well tank is sufficient to let water push through or not.

The first thing you need to do is to reset it, by flipping the switch up and back down or turning it off and then on. Then, you want to adjust the pressure cut-off value, which has to be 2-3 PSI more than the base value. This can be found in the manual as well.

Power Supply Issues

This is probably one of the first things your mind will tell you to check. If the well pump is seemingly okay and there is nothing wrong with the functions of the machine and it is just not working, then you might want to check whether it’s getting the power it needs to fire up or not.

There can be a wiring issue, a short circuit issue, or simply a faulty supply problem that is causing the pump to not work properly. So, check all of these things and you will find the problem. Once it is fixed, the pump will fire up again normally.

Obstruction In The Well

There are just a lot of ways by which a pump can get obstructed. Since the well is an open place, anything can fall in and cause a host of problems. There might be dirt, debris, or even sand stuck with water inside the pump. There might be something blocking the water from going up the pump in the pipes of the well and the list is just too long.

So, you want to troubleshoot the pump by checking all of the possible areas where there might be obstruction.

Damaged Well Pump Impeller

The pump impeller is the most important part of the well pump. It is a fan-like rotor attached at the bottom of the pump and this is what drives the water to produce the necessary pressure. However, sometimes, the impeller can also fall victim to damage and that can be highly frustrating.

There might be debris or sediments preventing the impeller from working properly. So, in this case, you will need to stop the pump and clean the impeller. If you’re not someone who has cleaned their impeller before then you’ll be in for a thick layer of surprise, because it does get really dirty.

The Pump Might Be Old

Another very common reason why your well pump might not be producing pressure or pumping water is the fact that your pump is just too old. Old pumps can get weary after a long time and even repairs can’t help them anymore. So, the only thing to do in this situation is to stop wasting money on useless repairs and consider well pump replacement Urbana.

This is the time to research the best well pump types out there and get one that is easy to maintain and to look after. It will only be helpful in the long run. Submersible well pumps are commonly used, but they are not right for every water well.

The Water Pressure Is Low

Low pressure is one of the most common problems in a well pump. This can happen due to multiple reasons. Either your well pump is not working properly and causing the well pressure to bleed or there is something wrong with the pressure tank and it is not keeping the pressure constant, which is also another issue itself.

To fix low water pressure, you need to take a look at your pressure tank and see whether the values are correctly set or not. This is going to ensure that the pump works on a definite value whenever it is powered on and doesn’t stop until the value is reached.

The Well Is Drying Up

Have you noticed that your well pressure decreases when it’s summer or very hot? Well, that can be the reason for your well drying up. This is common to occur in shallow wells or deep wells with not a lot of subsoil water.

This is bad because the only solution to this problem is digging up another well. This can be tedious, but if this is your only way of getting water, so be it.

There Is Trapped Air

This is common with submersible pumps. When they are submerged in water and turned on, first a blast of air moves through the entire pump, and then water replaces all of it. However, sometimes, that is just not possible and even water can leave a bit of air behind. This causes the impeller to stop working and that is not great at all.

So, to fix this, you need to keep the pump running until all of the air is pushed out of all of the trapped places in the pump and pipes. That’s how the pump will start to work again.

Clogged Water Filter

Water sediment filters are also an important addition to water well pumps. These are equipped to ensure that you don’t get contaminated water through your faucets, which is bad. So, sometimes, these water filters can need replacement and if they are clogged, then you can experience the problem of water not pumping properly in the well pump.

An easy way to check this is to put your water setting on bypass. If the water comes in easily, then you know that the filter is clogged and you need to do something about it. Luckily, changing water filters is super easy and after that, you won’t have any problem with the water or the pump.

You’ve Used Too Much Water

You might have just used too much water. Sometimes, when there are a lot of things going around in the house like you have guests over, you’re hosting people or some are even staying overnight, water usage can increase and it can cause you to overuse water and the water supply in the tank may run out. This can lead to the well pump working, but not really. So, that might also be a reason why your well pump is giving you a hard time.

The only way to rectify this is to turn on the pump and let the tank fill up with water. You can do this and then you can use water mindfully the next time so that you fall back into the cycle of things once again without any problems.

Conclusion

Well pumps not pumping water can be a very frustrating and stressful situation to deal with. Luckily now you know the reasons why it could happen so you can fix the pump immediately. Hire a well pump service Jefferson who can thoroughly inspect every aspect of your well water system and then perform the required repairs or replacements. tri